MS4985 is a bipolar micro-stepping motor driver chip with built-in 4-bit DAC, supporting full-step, 1/2, 1/4, and 1/8 stepping modes; it has a drive capability of up to 35V and ±1.5A.
MS4982 is a bipolar micro-stepping motor driver chip with built-in 4-bit DAC, supporting full-step, 1/2, 1/4, and 1/16 stepping modes; it has a drive capability of up to 35V and ±1.5A.
MS4932N is a three-phase sinusoidal brushless DC motor (BLDC) or permanent magnet synchronous motor (PMSM) controller. The chip processes Hall sensor signals and can achieve PWM switching by controlling the three-phase converter.
MS4933 is a three-phase sinusoidal brushless DC motor (BLDC) or permanent magnet synchronous motor (PMSM) controller. The chip processes Hall sensor signals and can achieve PWM switching by controlling the three-phase converter.
MS39545 is a sensorless three-phase DC motor driver chip using sinusoidal drive, featuring low noise and low vibration.
MS39549 is a sensorless three-phase DC motor driver chip using sinusoidal drive, featuring low noise and low vibration.
MS8829 is a three-phase brushless motor driver chip with a maximum operating voltage of 35V and a maximum drive current of 1.5A.
MS8828 is a three-phase brushless motor driver chip with a maximum operating voltage of 35V and a maximum drive current of 1.5A.
MS8313 provides three independently controllable half-H bridge drivers. It can be used to drive solenoids or other loads, mainly for driving a three-phase brushless DC motor.
MS4931 is a three-phase brushless motor pre-driver chip with a maximum operating voltage of 35V, suitable for driving a wide range of N-channel power MOSFETs. The chip features stall protection, over-temperature protection, and synchronous rectification.
MS3791 is a three-phase brushless motor pre-driver chip with a maximum operating voltage of 35V, suitable for driving a wide range of N-channel power MOSFETs. The chip features stall protection, over-temperature protection, and synchronous rectification.
MS3111D is a low-voltage 5V DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS3010 is a low-voltage 5V DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS3111S is a low-voltage 5V DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS3112 is a dual-channel 5V full-bridge driver chip that can be used as a stepper motor driver. It provides an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS3122 is a dual-channel full-bridge driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS3142/MS3142S is a dual full-bridge motor driver. The power supply voltage range is 4V to 18V, with an average current of 1.1A and a peak current of 1.54A. For higher current capability, the dual full bridges can be used in parallel.
MS3145D is a dual full-bridge motor driver. The power supply voltage range is 4V to 18V, with an average current of 1.1A and a peak current of 1.54A. For higher current capability, the dual full bridges can be used in parallel.
MS8837 is a DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS8838 is a DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS31001 is a low-voltage 5V DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS31011 is a low-voltage 5V DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS31051S/D is a low-voltage 5V DC motor driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS8847 is a dual H-bridge driver circuit, suitable for home appliances and other mechatronic applications. The device can be used to drive a stepper motor or other loads. Each output driver channel contains N-channel power MOSFETs in an H-bridge configuration.
MS8844 provides four independently controllable half-H bridge drivers. It can be used to drive DC motors, a stepper motor, four solenoids, or other loads. Each output driver channel contains N-channel power MOSFETs in a half-H bridge configuration.
MS3114 is a four-channel low-voltage 5V full-bridge driver chip, providing an integrated motor drive solution for cameras, consumer products, toys, and other low-voltage or battery-powered motion control applications.
MS4553M is a bidirectional level shifter that can be used in mixed-voltage digital signal systems. It uses two independent power supplies; the A-side supply voltage range is 1.65V to 5.5V, and the B-side supply voltage range is 2.3V to 5.5V.
MS6212D is a bidirectional level shifter that can be used in mixed-voltage digital signal systems. It uses two independent power supplies; the A-side supply voltage range is 1.65V to 5.5V, and the B-side supply voltage range is 2.3V to 5.5V.
MS4553S is a bidirectional level shifter that can be used in mixed-voltage digital signal systems.
MS3814 is a TMDS equalizer/driver chip used to compensate for losses in FR-4 and cables to DVI/HDMI connectors. It provides outputs that fully meet DVI/HDMI TMDS requirements.
MS3815 is an adaptive equalizer chip that compensates for attenuation in DVI, HDMI, DFP, PanelLink, and ADC cables, extending the transmission distance of the cables.
This single low-noise block converter regulator (LNBR) is suitable for analog and digital satellite receivers and is a monolithic linear switching voltage regulator.
MS2351M is a logarithmic amplifier chip mainly used for received signal strength indication (RSSI) and power amplifier control, with an operating frequency range of 100M to 2500MHz and a typical dynamic range of 45dB.
GaN, Chinese name: Gallium Nitride, has a wurtzite structure at room temperature and pressure. It is the core material for blue light-emitting diodes in semiconductor lighting today.
This power module is a 65W single C interface, and its output voltage can be controlled by the protocol IC to provide 5V/3A, 9V/3A, 15V/3A, 20V/3.25A, etc.
iML7278 is an application for a 13-channel high-voltage level shifter.
iML7276 is an application for a 19-channel high-voltage level shifter.
iML7272A is a high-voltage level shifter. This device is suitable for GOA TFT-LCD panel applications.
iML1942 is a highly integrated power management IC for TFT LCD panels.
The ES9311Q dual ultra-low noise +3.3V regulator is an industry-leading, ultra-low noise regulator that provides the reference voltage for ESS 32-bit Sabre DACs.
P1032BF1 is a microcontroller based on ARM Cortex-M3, specifically designed for Wi-Fi/Bluetooth communication control.
MS1651 is a single-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS1671 is a single-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS1676 is a single-channel video amplifier chip with a built-in 12dB gain rail-to-rail output driver and a 10th-order filter, with a -3dB bandwidth of 30MHz.
MS1681 is a single-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS1683 is a video buffer with selectable bandwidth. It integrates a 6dB gain rail-to-rail output driver and a 10th-order output reconstruction filter, allowing the same input signal to be selected between -1dB bandwidths of 35MHz and 56MHz.
MS2267 is a dual-channel amplifier with 6dB gain and 75-ohm load drive, suitable for S-VHS VCR, HI-BAND, VCR, etc. Each channel integrates a clamp circuit and drive circuit, and can directly connect to a TV display.
MS2631 is a single-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 10th-order output reconstruction filter.
MS2681 is a single-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 10th-order output reconstruction filter.
MS6363 is a 3-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS6364 is a 3-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS6365T is a 5-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS6367 is a 3-channel video buffer with a built-in 6dB gain rail-to-rail output driver and a 6th-order output reconstruction filter.
MS7332M is a chip that integrates a single-channel video amplifier and video coaxial line control decoding.
MS7335M is a chip that integrates a single-channel video amplifier and video coaxial line control decoding.
MS7336M is a chip that integrates a single-channel video amplifier and video coaxial line control decoding, and is also a video amplifier with selectable bandwidth.
MS7336MA is a chip that integrates a single-channel video amplifier and video coaxial line control decoding. It integrates a 6dB gain rail-to-rail output driver and a 10th-order filter.
